BMP280 Barometric Pressure & Temperature Sensor Module | I2C/SPI Compatible
-
High-precision BMP280 barometric pressure and temperature sensor
-
Supports I2C and SPI communication interfaces
-
Measures pressure: 300–1100 hPa and temperature: -40°C to +85°C
-
Compact PCB for easy integration into DIY projects
-
Ideal for weather stations, altimeters, and IoT devices
-
Low power consumption for battery-powered electronics
-
Compatible with Arduino, Raspberry Pi, ESP32, and other microcontrollers
-
Reliable sensor module for students, hobbyists, and electronics engineers
199.00৳ 300.00৳
The BMP280 sensor module provides precise barometric pressure and temperature readings, making it perfect for weather monitoring, altitude detection, and IoT applications. Its small form factor allows easy integration into embedded systems, and its I2C/SPI interface ensures compatibility with a wide range of microcontrollers.
FAQs
Q1: What is the pressure measurement range?
300–1100 hPa.
Q2: Can it measure temperature?
Yes, -40°C to +85°C.
Q3: Which microcontrollers is it compatible with?
Arduino, Raspberry Pi, ESP32, and similar boards.
Specification Table
| Parameter | Value |
|---|---|
| Pressure Range | 300–1100 hPa |
| Temperature Range | -40°C to +85°C |
| Interfaces | I2C / SPI |
| Operating Voltage | 3.3V–5V DC |
| Applications | Weather stations, Altimeters, IoT devices |
| Module Size | ~20 × 15 mm |
Based on 0 reviews
Be the first to review “BMP280 Barometric Pressure & Temperature Sensor Module | I2C/SPI Compatible”
Related products
-
Modules and Shields
4 Channel Wireless RF Remote Control Module 315MHz | Transmitter and Receiver Non-Locking
-15%
Modules and Shields4 Channel Wireless RF Remote Control Module 315MHz | Transmitter and Receiver Non-Locking
-
4-channel wireless RF remote control system with 315MHz frequency
-
Non-locking (momentary/jog) mode – signal only active while button is pressed
-
Receiver sensitivity up to -98dB for stable long-range performance
-
Typical range: 30–50m indoors, up to 200m outdoors (line of sight)
-
Compact receiver board with output pins: D0, D1, D2, D3, VT
-
Uses ASK modulation for reliable communication with low interference
-
Transmitter power: 10mW @ 12V, low power consumption design
-
Perfect for electric locks, garage doors, lighting systems, robotics, and DIY automation projects
SKU: n/a -
-
Modules and Shields
6S 12A Li-ion Lithium Battery BMS | 18650 Cell Protection & Charger Module
-
High-quality 6S BMS board for Li-ion 18650 battery packs
-
Continuous discharge current: 12A, ideal for moderate-power applications
-
Provides overcharge, over-discharge, overcurrent, and short-circuit protection
-
Supports automatic cell balancing to extend battery life
-
Works with 3.6V–3.7V Li-ion cells, including 18650 and LiPo batteries
-
Compact PCB design for easy integration into battery packs
-
Suitable for electric scooters, DIY battery packs, e-bikes, and robotics projects
-
Reliable and safe high-current battery management system for hobbyists and professionals
SKU: n/a -
-
Modules and Shields
3S 15A 12.6V Li-ion Lithium Battery Protection BMS Board | 18650 Pack Charging Module
-40%
Modules and Shields3S 15A 12.6V Li-ion Lithium Battery Protection BMS Board | 18650 Pack Charging Module
-
Suitable for 3-cell (3S) Li-ion/LiPo packs (11.1V / 12.6V)
-
Provides overcharge, over-discharge, short-circuit & overcurrent protection
-
Continuous current: 15A, compact PCB design
-
Perfect for DIY 18650 packs, LED drivers, robotics, and low-power inverters
SKU: n/a -
-
Modules and Shields
16 Channel PWM Servo Motor Driver Controller PCA9685 12-Bit I2C Module
-
Controls up to 16 servos or LEDs with precise PWM signals
-
12-bit resolution for smooth and accurate motion control
-
Uses I2C interface, compatible with Arduino and Raspberry Pi
-
Perfect for robotics, automation, and DIY electronics projects
SKU: n/a -
There are no reviews yet.